Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
This article below in relation to Tools You Need to Install a New Bathtub is unquestionably entertaining. Give it a try and make your own personal ideas.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a bathtub isn't specifically rocket science, but it does need solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old tub with a new one is additionally a moderately hard job. If the old bathtub is easily accessible, the job can move immediately; if you need to open a wall to get rid of the old tub and also place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the job as well as fit attempting it. Instead of hiring a contractor to take over a halfway-completed task, it is better to consider utilizing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your bathroom if you have currently acquired a new tub and also don't need to alter the setup of your previous water pipes.
Your tools as well as product list should make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing taps can be fairly troublesome because of the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washers remain in area between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing both wood boards under its feet, place the bath tub in the needed position. The wood boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub and likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and securing around the tub needs to wait up until the bath tub has been utilized at the very least once as this will resolve it right into its final setting.
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to prevent pressure on the bathtub.
Fit the adaptable faucet ports to the bottom of both faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to break a rigid seal, creating the water to permeate the wall in between the bathroom and also the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can split relatively early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader on How to Install a Bathtub, I thought sharing that short article was worthwhile. Enjoyed reading our post? Please share it. Help others check it out. We take joy in reading our article about Tools You Need to Install a New Bathtub .
Click For More Info Report this page